Extron electronics MultiMatrix SMX System Setup Manual Download Page 22 | Manualshive

Page: 22 / 48

background image

16

SMX System MultiMatrix Switcher • Front Panel Operation

Using Reset Levels

The rear panel has a recessed Reset button (see

) that initiates

four levels of resets (numbered 1, 3, 4, and 5). Use a pointed stylus,
ballpoint pen, or Extron Tweeker to access it and select the reset level.
See the

Reset Mode Table

on page 17 for a summary of the modes.

CAUTION:

Review the reset modes carefully. Using the wrong
reset mode may result in unintended loss of flash
memory programming, port reassignment, or a
controller reboot.

NOTES:

•

The reset modes listed below close all open IP and

Telnet connections and sockets. Also, the following
modes are separate functions, not a continuation from
mode 1 to mode 5.

•

If the reset button is continuously held down, the I/O
lights flash every 3 seconds as the next reset level is
reached, corresponding to modes 3, 4, and 5.

Reset Mode Uses

Use mode 1 to revert to the factory default firmware version if
compatibility issues arise with user-loaded firmware (see

on

page 17).
Use mode 3 to restart the communication and control events.
Use mode 4 to reset most IP protocols to their default settings.
Use mode 5 to restore the switcher to the default conditions.

NOTE:

Mode 5 reset clears most adjustment. To save these

settings, use the SMX Control Program and the

File >

Save MATRIX settings as...

selection before you

perform this reset (see

Configuration and Control

on

page 32).

RESET

RESET

RESET

RESET

Release, then

immediately

press and release again. Reset
LED flashes in confirmation.

Modes 3, 4, and 5

Press and

hold

the Reset button.

Mode 1

Reset LED flashes

once,

twice, or three times.

Press and

hold for

3, 6, or 9 seconds.

Apply Power

1

2

RESET

Release the Reset button.

«
...
20
21
22
23
24
...
»

Summary of Contents for MultiMatrix SMX System

















































Reviews:

No comments

Related manuals for MultiMatrix SMX System

Brand: CAME Pages: 2

Brand: I-Tech Pages: 27

Brand: Kramer Pages: 61

Brand: Tripp Lite Pages: 80

Web-Smart GS-1208M

Brand: Ruby Tech Pages: 2

Brand: Atlantis Land Pages: 3

Brand: Sams Pages: 14

Brand: PRO SIGNAL Pages: 2

Brand: Labgear Pages: 8

Brand: H3C Pages: 3

Brand: Black Box Pages: 50

SECURVIEW SV-7020

Brand: CrimeStopper Pages: 1

Brand: WELLTECH Pages: 280

Brand: Hamlet Pages: 2

Brand: Rosewill Pages: 10

Brand: N-Tron Pages: 15

Brand: CoolGear Pages: 8

PoE Giga-MiniMc

Brand: IMC Networks Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands