Extron electronics MultiMatrix SMX System Setup Manual Download Page 23 | Manualshive

Page: 23 / 48

background image

17

SMX System MultiMatrix Switcher • Front Panel Operation

Reset Mode Table

Mode

Action

Result

1

Hold down the recessed
Reset button while applying
power to the switcher.

Defaults switcher to factory installed
firmware. Event scripting will not start if
the switcher is powered on in this mode. All
user files and settings (drivers, adjustments,
IP settings, and so on) are maintained (see

below).

3

Hold down the Reset button
for 3 seconds, until the Reset
LED blinks once, then press
Reset momentarily
(<1 second) within 1 second.

Mode 3 turns events on or off. During
resetting, the Reset LED flashes 2 times if
events are starting, 3 times if events are
stopping.

4

Hold down the Reset button
for 6 seconds, until the Reset
LED blinks twice (once at 3
seconds, again at 6 seconds)
then press Reset momentarily
(<1 second) within 1 second.

Mode 4:

•

Enables ARP capability

•

Sets IP address to factory default

•

Sets subnet address to factory default

•

Sets gateway address to factory default

•

Sets port mapping to factory default

•

Turns DHCP off

•

Turns events off

The Reset LED flashes four times in quick
succession confirming the Reset.

5

Hold down the Reset button
for 9 seconds, until the Reset
LED blinks three times (once
at 3 seconds, again at 6
seconds, and then again at
9 seconds). Then press Reset
momentarily (<1 second)
within 1 second.

Mode 5 performs a complete reset to
factory defaults (with the exception of the
firmware):

•

Does everything mode 4 does

•

Resets almost all real time adjustments:
clears all ties and presets, clears all audio
or RS-232 mutes, clears all I/O grouping,
clears all RGB delay settings to zero, and
clears all input and output audio settings
(see the

SMX User Guide

for more details

on these features)

•

Resets all IP options

•

Removes/clears all files for the SMX

The reset LED flashes four times in quick
succession confirming the reset.

NOTES:

•

After a mode 1 reset is performed, update the firmware

to the latest version. Do not operate the SMX firmware
version that results from the mode 1 reset. To use factory
default firmware, upload that version again.

•

If you do not want to update firmware, or you performed
a mode 1 reset by mistake, cycle power to the SMX to
return to the firmware version that was running before
the mode 1 reset. Use the

0Q

SIS command to confirm

that the factory default firmware is no longer running
(look for the asterisk [*] following the version number.

«
...
21
22
23
24
25
...
»

Summary of Contents for MultiMatrix SMX System

















































Reviews:

No comments

Related manuals for MultiMatrix SMX System

Brand: CALIENT Pages: 22

Brand: DANLERS Pages: 2

Brand: Ubiquiti Pages: 24

Brand: Ubiquiti Pages: 13

Brand: Ubisys Pages: 2

S6520X-EI Series

Brand: H3C Pages: 34

Brand: Metra Electronics Pages: 8

Brand: Xantech Pages: 32

Extricom AT-EXLS-3000

Brand: Allied Telesis Pages: 120

Brand: Thinklogical Pages: 45

Brand: Teltronics Pages: 82

Brand: Network Technologies Pages: 46

Brand: Pilz Pages: 8

Brand: RITS-N Pages: 2

Hirschmann GREYHOUND GMM20

Brand: Belden Pages: 96

PowerSwitch EDSR

Brand: Leviton Pages: 13

Brand: Abocom Pages: 2

Brand: Tvone Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands