Extron electronics DTP CrossPoint 108 4K, Setup Manual

Page: 13 / 44

5 DTP CrossPoint 4K Series • Installation
50-60 Hz
100-240V ~ -- A MAX
1 2
1 2 3 4 5 6
3A 4A 4B 4
RS-232 IR
RS-232 IR
Tx Rx Tx Rx G
Tx Rx Tx Rx
XTP
RESET
S/PDIF
OUT
DTP
XTP
DTP
XTP
DTP
XTP
DTP
+48V
MIC/LINE
1 1
3
2 4
2
3
4
EXP
HDBT
HDBT
G
7 8
DTP CROSSPOINT 84 4K
RS-232 IR
Tx Rx Tx Rx G
RS-232 IR
Tx Rx Tx Rx G
OVER TP
OVER TP
AUDIO OUTPUT
S
AUDIO INPUTS DMP EX
PA
NSION
INPUTS
OUTPUT
S 3B
1
L R
1
R
3
L R
3
L L R
5
L R
2
L R
4
L R
2
L R
4
L R
6
L R
Tx Rx G
REMOTE
AMP OUTPUT
CLASS 2 WIRING
1
100V
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
IN
SIG LINK
IN
R
CONTROL
Tx Rx
RTSCTS
G
1 2 1 2
S G S G
C 3 4 C +V
PWR OUT = 6W
+V D -S +S
Tx Rx G Tx Rx G 1 2 3 4 G
COM 1 COM 3 COM 2 DIGITAL I/O
AV LAN 2
LAN AV LAN 1
IR/SERIAL RELAYS DIGITAL I/O
AV LAN 3
A B C C B
D E E F F
Figure 3. Video Input and Output Connectors, 8x4 Matrix
A
HDMI inputs 1 through 6 (see figure 2 on page 4 and
figure 3) — Plug HDMI digital video sources (or DVI
with appropriate adapters) into these HDMI ports. See
HDMI connectors
on page 11 to secure the connector to the
enclosure with a LockIt HDMI Cable Lacing Bracket.
B TP (XTP/DTP) switches (see figure 2 and figure 3) —
XTP
DTP
ATTENTION:
• Position this switch
BEFORE
connecting the
appropriate device to the TP connector. Failure to
comply can damage the endpoint.
• Positionnez le sélecteur
AVANT
de connecter
l’appareil approprié au connecteur TP. Ne pas
respecter cette procédure pourrait endommager le
point de connexion.
The following table identifies the inputs with TP switches by
matrix size.
Matrix Inputs Matrix Inputs
10x8 7 through 10 All others 7 and 8
XTP position — Select if the transmitting device is an
Extron XTP matrix switcher. The input consists of HDMI with
embedded audio plus RS-232 and IR.
DTP position
— Select if the transmitting device is an Extron
DTP device. The input consists of HDMI with embedded audio,
analog audio, and RS-232 and IR. The switcher can provide
remote power to the transmitter.
C
TP inputs (see figure 2 and figure 3)— Plug
SIG LINK
IN
compatible Extron DTP or XTP signals into these
RJ-45 ports using TP cables. See
TP connectors on
page 12 to wire the connectors.
ATTENTION:
• Do not connect this port to a computer data or
telecommunications network.
• Ne connectez pas ces port à des données informatiques
ou à un réseau de télécommunications.
3