background image

1. 

Product information

Description

The EBC20 (

exodraft

 Boiler Control) is a specially designed control component for constant pressure regulation of 

chimney draft. The EBC20 comes in two versions:

•  EBC20EU01 for indoor installation

•  EBC20EU02 for outdoor installation

By changing the operating mode, the EBC20 can also:

•  Act as a 2-stage speed regulator (see section 3).

•  Control the supply of fresh air to the boiler room (see section 4).

Layout of the instructions

The EBC20 can control an 

exodraft

 chimney fan or an 

exodraft

 supply air fan. 

There are seven sections to the instructions:

•  Read section 1. ”Product information”. 

•  Read the section that deals with the required control methods:

 

Œ

Section 2: Pressure-controlled regulation of 

exodraft

 fans (factory-set).

 

Œ

Section 3: Two-step speed regulation of 

exodraft

 fans.

 

Œ

Section 4: Pressure-controlled regulation of 

exodraft

 supply air fan. 

•  Read sections 5–7.

Section 2,3, and 4 deals with the following:

Section 2:        

 Pressure-controlled regulation of 

exodraft

 chimney fans (default).

•  The EBC20 ensures and monitors constant pressure in a chimney.

•  The EBC20 is designed for use with boiler systems with 1- and 2-stage burners. 

•  The EBC20 can also be used for boiler systems with modulating burners.

•  The control system monitors chimney draft and shuts down the burner in the event of errors (the alarm-

diode on the EBC20 will turn on).

•  The control system is intended for both solid fuel boilers, atmospheric gas boilers, condens and forced 

draft boilers for oil and gas.

•  The EBC20 can control a chimney fan directly or indirectly via a frequency converter. 

Section 3:        

 2-stage speed regulation of 

exodraft

 chimney fans.

•  The EBC20 can be used as a 2-stage speed regulator for 

exodraft

 chimney fans.

•  The EBC20 monitors chimney draft and shuts down the burner in the event of errors (the alarmdiode on 

the EBC20 will turn on). 

•  The control system is intended for 1- or 2-stage atmospheric gas boilers.

•  The EBC20 can control a chimney fan directly or indirectly via a frequency converter. 

Section 4:        

 Pressure-controlled regulation of 

exodraft

 supply air fans.

•  The EBC20 can be used to control an 

exodraft

 BESB or BESF box fan.

•  The EBC20 ensures and monitors constant pressure in a boiler room.

•  The control system monitors the pressure in the boiler room and shuts down the burner in the event of 

errors (the alarmdiode on the EBC20 will turn on).

•  The EBC20 can control a supply air fan directly or indirectly via a frequency converter. 

3002878-EBC20-UK

• Product information

• Product information

Summary of Contents for EBC20









































Reviews: