manualshive.com logo in svg

EXFO bv10, User Manual, Page: 8 / 116

Share
Download
EXFO bv10 User Manual Download Page 8

Introducing the BV10

2

BV10

BrixWorx for Turn Up

BrixWorx for Turn Up 

BrixWorx for Turn Up is a system designed for Turn-Up and reflector testing 
with no monitoring capability. BrixWorx for Turn Up supports a central 
management system, Verifier management for the supported Verifier 
models, and user management. BrixWorx for Turn Up does not support 
active or passive testing. 

The BV10 Verifier is designed specifically for Ethernet OAM Handling, UDP 
Echo Responder, TWAMP Light Responder, and Smart Loopback test 
features. These features are enabled by loading the tests on the Verifier 
Information page (Additional Services section) and in some cases 
specifying parameters, such as a UDP Listening port for TWAMP or the 
mode for Smart Loopback.

For more information, refer to the 

BrixWorx for Turn Up Getting Started

 

guide to learn more about the features of the BrixWorx for Turn Up system 
and the 

BrixWorx User Guide

 to learn more about the Verifier Information 

page.

Summary of Contents for bv10





















































































































Reviews:

No comments