manualshive.com logo in svg

EXFO bv10, User Manual, Page: 52 / 116

Share
Download
EXFO bv10 User Manual Download Page 52

CLI Command Reference

46

BV10

Operation Commands

Software Management Commands

show sysinfo 

Description

Displays the following BV10 unit information:

Software/firmware versions

Hardware model, version, and identification 

Serial number

Manufacturing date

Unit Health Status of the test port: LINK DOWN or OK (link up)

DC Feed A Status, DC Feed B Status. Applied to DC version only and 

are monitored every 5 seconds. 

Syntax

show sysinfo 

Example

bv10-100>

 show sysinfo

S/W VERSION

: Linux 2.6.25 #8 Wed Apr 16 14:47:51 EDT 2014

H/W

: BV10-1000-AC

H/W VERSION 

: C

H/W ID

: 800000638428

SERIAL NUMBER

: 638428

MFG DATE

: 23-03-12

UNIT HEALTH 

: OK

show version 

Description

Displays the current software/firmware versions.

Syntax

show version 

Example

bv10-100>

 show version

S/W VERSION

: Linux 2.6.25 #8 Wed Apr 16 14:47:51 EDT 2014

F/S VERSION

: 4.0.1.2, Thu Aug 21 11:50:11 EDT 2014

F/W VERSION

: 10021906

Summary of Contents for bv10





















































































































Reviews:

No comments