manualshive.com logo in svg

EXFO bv10, User Manual, Page: 68 / 116

Share
Download
EXFO bv10 User Manual Download Page 68

CLI Command Reference

62

BV10

Configuration Commands

console in-band enable|disable 

Description

Enables or disables in-band management on the Test port. By default, 

in-band management on the Test port is enabled.
This command displays no output unless there is an error.
This command is not available through the Test port. 

Syntax

console in-band enable|disable

Example

bv10-100>

 console in-band disable

console in-band port 

port_value 

Description

Configures the port number that can be used to communicate with the 

BrixWorx server from the Test port. 

Syntax

console in-band port 

port_valueh 

Example

bv10-100>

 console in-band port 300 

console telnet|ssh|serial idle-timeout 

value_in_seconds 

Description

Sets the idle timeout for the Telnet server, SSH server, or serial console 

communication session. Each connection method can have its own 

timeout. 
By default, no idle timeout is set. The minimum idle timeout is 30 

seconds. To disable the idle timeout, enter 0 (zero).
This command displays no output.

Syntax

console telnet|ssh|serial idle-timeout 

value_in_seconds

Example

bv10-100>

 console telnet idle-timeout 900

Summary of Contents for bv10





















































































































Reviews:

No comments