manualshive.com logo in svg

EXFO bv10, User Manual, Page: 69 / 116

Share
Download
EXFO bv10 User Manual Download Page 69

CLI Command Reference

BV10-100 and BV10-1000

63

Configuration Commands

Interface Configuration Commands

The following commands allow setting the port interface parameters such 
as the IP addressing (static IP or DHCP), auto-negotiation (speed, duplex, 
flow control), VLAN support, transceiver (electrical or optical), laser (ON or 
OFF), and cable (straight or auto detection). 

Note:

Most of the interface commands do not display output. Use the 

show interface

 

(see page 51) and 

show config

 (see page 59) commands to display the 

BV10’s current interfaces and configuration. 

Note:

For the 

TEST

 port: 

Duplex

 and 

Flow Control

 are not configurable and 

respectively set to 

Full

 and 

None

. 

interface test transceiver electrical|optical 

Description

Sets the TEST port transceiver type to either electrical or optical. 
This command applies to the BV10-1000 only. 
This command cannot be sent through the Test port. 

Syntax

interface test transceiver electrical|optical 

Example

bv10-100>

 interface test transceiver optical 

interface test laser on|off 

Description

Turns the laser of the TEST optical interface on or off. 
This command applies to the BV10-1000 only and is available only 

when the transceiver type is set to optical. 
This command cannot be sent through the Test port. 

Syntax

interface test laser on|off 

Example

bv10-100>

 interface test laser on 

Summary of Contents for bv10





















































































































Reviews:

No comments