manualshive.com logo in svg

EXFO bv10, User Manual, Page: 22 / 116

Share
Download
EXFO bv10 User Manual Download Page 22

Physical Interfaces, LEDs, and Buttons

16

BV10

Port Availability on BV10

Port Availability on BV10 

Connecting the TEST Port Interface 

The BV10-100 provides an electrical 10/100 Mbit/s Ethernet Test interface 
while the BV10-1000 provides an electrical 10/100/1000 Mbit/s and an 
optical 1000 Mbit/s SFP laser Ethernet Test interfaces. The two BV10-1000 
Test interfaces are mutually exclusive. 

RJ45 Port 

Connect the 10/100/1000 Mbit/s electrical interface to be tested to the RJ45 
test port. The electrical ports is RJ45 for category 5 unshielded twisted pair 
(UTP). Refer to 

Ethernet Cables

 on page 102 for cable specifications. 

Supported electrical rates are:

For BV10-100: 10 Mbit/s and 100 Mbit/s.

For BV10-1000: 10 Mbit/s, 100 Mbit/s, and 1000 Mbit/s.

Port 

Label

Description

Model

BV10-100 BV10-1000

TEST PORT

10/100 Mbit/s electrical RJ45 Test port (10Base-T and 100Base-TX)

X

10/100/1000Mbit/s electrical RJ45 Test port (10Base-T, 100Base-TX 
and 1000Base-T)

X

1000 Mbit/s optical SFP Test port (1000Base-SX/LX/ZX; 
850/1310/1550nm)

X

LAN

10/100 Mbit/s electrical Management port

X

X

CONSOLE

RS-232 DE-9F DCE (referred as DB9) Console port

X

X

Summary of Contents for bv10





















































































































Reviews:

No comments