manualshive.com logo in svg

EXFO bv10, User Manual, Page: 29 / 116

Share
Download
EXFO bv10 User Manual Download Page 29

BV10-100 and BV10-1000

23

5

Managing BV10 Verifier on 

BrixWorx 

This chapter describes how to configure and use BV10 hardware on 
BrixWorx. It explains the CLI commands used to communicate with the 
BrixWorx registry and describes how to set up tests using the BrixWorx 
user interface. 

Note:

When the BV10 is used in a BrixWorx environment, you must use BrixWorx 
GUI rather than CLI prompt to manage the BV10 device. When you change 
a reflector to run or not through the CLI, this is not updated on the BrixWorx 
GUI Additional Services page. The GUI changes override the changes done 
using the CLI prompt.

Configuring BV10 Verifier for BrixWorx 

Registry 

The BV10 Verifier must be configured before you can use it in the BrixWorx 
system. Once the configuration of a BV10 Verifier is complete, you must 
add it to BrixWorx just like any other Verifier. 

Configure the BV10 Verifier 

To configure the BV10 Verifier for use in the BrixWorx system: 
1.

Access the CLI prompt using Telnet or SSH. To log on to the Telnet or 
SSH server, use the following login information: 

Login ID: 

exfo

Password: 

exfo123

The CLI prompt name contains the BV10 model number followed by 

(DEBUG)

. For example:

BV10-1000 (DEBUG)>

 

2.

To configure the IP address of the local BrixWorx registry, type the 
following command: 

BV10-1000 (DEBUG)>

 server discovery local 

IP address

 

Summary of Contents for bv10





















































































































Reviews:

No comments