4. Seat Sliding Tube, Back/Seat Support Bracket, and Handlebar
Remove eight
Support Bracket
Wrench
Insert
Frame
Attach the
with eight
Tighten
Adjust the
Knob
M12x33
directio
Attach the
M8x45
M8 Cap Nut
Screwdriver
Connect the
Frame
Seat Sliding Tube, Back/Seat Support Bracket, and Handlebar
Remove eight M8x15
Support Bracket
Wrench provided.
Insert the Seat Sliding Tube
Frame (3).
Attach the Seat Sliding Tube
with eight M8x15
Tighten bolts with
Adjust the seat position and insert the Round Knob (
Knob (77), and
x33 Triangle Knob
direction to tighten.
Attach the Handlebar
M8x45 Bolts (70), two
Cap Nuts (32).
Screwdriver provided.
Connect the Middle
Frame (3) to the
Seat Sliding Tube, Back/Seat Support Bracket, and Handlebar
M8x15 Bolt
Support Bracket (1) and Seat Sliding Tube
vided.
Seat Sliding Tube
Seat Sliding Tube
M8x15 Bolts (23) and eight
with the Allen Wrench
eat position and insert the Round Knob (
and M12x27 Triangle Knob
Triangle Knob (77),
n to tighten.
Handlebar (13) onto the
s (70), two Ø8
s (32). Tighten
provided.
Middle Section Hand Pulse Sensor Wire
(3) to the Hand Pulse Sensor
Seat Sliding Tube, Back/Seat Support Bracket, and Handlebar
Bolts (23) and eight
Seat Sliding Tube
Seat Sliding Tube (15) into the Bushings (54) of the
Seat Sliding Tube (15) to the
s (23) and eight
the Allen Wrench
eat position and insert the Round Knob (
Triangle Knob
(77), and M12
(13) onto the
Ø8 Curve Washer
Tighten bolts w
ection Hand Pulse Sensor Wire
Hand Pulse Sensor
ASSEMBLY
Seat Sliding Tube, Back/Seat Support Bracket, and Handlebar
s (23) and eight Ø8
Seat Sliding Tube (15). Remove
(15) into the Bushings (54) of the
(15) to the Back
s (23) and eight Ø8 Washer
the Allen Wrench provided.
eat position and insert the Round Knob (
Triangle Knob (66). Turn the
M12x27 Triangle Knob
(13) onto the Back and Seat Support Bracket
Curve Washers (25), two
bolts with the Multi Hex Tool
ection Hand Pulse Sensor Wire
Hand Pulse Sensor Wire (68) from the
ASSEMBLY
12
Seat Sliding Tube, Back/Seat Support Bracket, and Handlebar
Washers (24) from the
(15). Remove
(15) into the Bushings (54) of the
Back and Seat Support Bracket
Washers (24) that were removed.
provided.
eat position and insert the Round Knob (17)
. Turn the Round Knob (
Triangle Knob
and Seat Support Bracket
s (25), two Ø8
Multi Hex Tool
ection Hand Pulse Sensor Wires (55) from the
Wire (68) from the
ASSEMBLY
Seat Sliding Tube, Back/Seat Support Bracket, and Handlebar
s (24) from the
(15). Remove bolts with
(15) into the Bushings (54) of the Rear Main
and Seat Support Bracket
s (24) that were removed.
), M12x33
Round Knob (
Triangle Knob (66) in the
and Seat Support Bracket
Washers (24), and two
Multi Hex Tool with Phillips
s (55) from the
Wire (68) from the Handlebar
Tool:
Multi Hex Tool with
Phillips Screwdriver
Seat Sliding Tube, Back/Seat Support Bracket, and Handlebar
Installation
s (24) from the Back/Seat
with the Allen
Rear Main
and Seat Support Bracket (1)
s (24) that were removed.
x33 Triangle
Round Knob (17),
in the clockwise
and Seat Support Bracket (1) with two
s (24), and two
with Phillips
s (55) from the Rear Main
Handlebar (13).
Allen Wrench S6
Tool:
Multi Hex Tool with
Phillips Screwdriver
Installation
Seat
the Allen
(1)
s (24) that were removed.
clockwise
(1) with two
s (24), and two
Rear Main
Allen Wrench S6
Multi Hex Tool with
Phillips Screwdriver