TROUBLESHOOTING
The recumbent bike
There is no display on the computer
console.
There is n
reading or
The recumbent bike
noise when in use
Cleaning
The recumbent bike
abrasives or solvents
recumbent bike
computer
Please keep
to prevent screen damage.
Please i
every week
Storage
Store the
TROUBLESHOOTING
PROBLEM
recumbent bike
There is no display on the computer
There is no heart rate reading
or is erratic
recumbent bike
when in use.
Cleaning
recumbent bike
abrasives or solvents
recumbent bike after each use.
computer display panel as this
Please keep the recumbent bike
prevent screen damage.
Please inspect all assembly bolts and pedals on the machine for proper tightness
week.
Storage
Store the recumbent bike
TROUBLESHOOTING
PROBLEM
recumbent bike wobbles when in use.
There is no display on the computer
rate reading
/ inconsistent.
recumbent bike makes a squeaking
TROUBLE SHOOTING & MAINTENANCE
recumbent bike can be cleaned with a soft cloth and mild detergent. Do not use
abrasives or solvents on plastic parts
after each use.
display panel as this
recumbent bike
prevent screen damage.
nspect all assembly bolts and pedals on the machine for proper tightness
recumbent bike in a clean and dry environment
TROUBLESHOOTING
PROBLEM
wobbles when in use.
There is no display on the computer
rate reading or heart rate
inconsistent.
makes a squeaking
TROUBLE SHOOTING & MAINTENANCE
can be cleaned with a soft cloth and mild detergent. Do not use
on plastic parts.
after each use. Be careful not get excessive moisture on the
display panel as this might cause an electrical hazard or electronics to fail.
recumbent bike, specially, the
prevent screen damage.
nspect all assembly bolts and pedals on the machine for proper tightness
in a clean and dry environment
TROUBLESHOOTING
wobbles when in use.
Turn the
stabilizer
bike.
1. Remove the
the
console
wires that come from the front handlebar
post.
2. Check if the
positioned and battery springs are
proper contact
3.
The batter
be dead.
or heart rate
1. Make sure that the
the
2. To
precise, please always hold on to the
handlebar grip sensors with two hands
instead of just with one hand only when
you try to test your heart rate figures.
3. Gripping the
Try to maintain
holding onto the
makes a squeaking
The bolts may
please inspect
bolts.
TROUBLE SHOOTING & MAINTENANCE
can be cleaned with a soft cloth and mild detergent. Do not use
. Please
Be careful not get excessive moisture on the
might cause an electrical hazard or electronics to fail.
, specially, the computer
nspect all assembly bolts and pedals on the machine for proper tightness
in a clean and dry environment
19
SOLUTION
Turn the rear stabilizer end cap
stabilizer as needed to level the
Remove the
the wires that come from the computer
console are
wires that come from the front handlebar
post.
Check if the
positioned and battery springs are
proper contact
The batteries
be dead. Change to new batteries.
Make sure that the
the hand pulse
To ensure the pulse readout is more
precise, please always hold on to the
handlebar grip sensors with two hands
instead of just with one hand only when
you try to test your heart rate figures.
Gripping the
Try to maintain
holding onto the
The bolts may be
please inspect the bolts and tighten the loose
TROUBLE SHOOTING & MAINTENANCE
can be cleaned with a soft cloth and mild detergent. Do not use
Please wipe your perspiration off the
Be careful not get excessive moisture on the
might cause an electrical hazard or electronics to fail.
computer console, out of direct sunlight
nspect all assembly bolts and pedals on the machine for proper tightness
in a clean and dry environment
SOLUTION
rear stabilizer end cap
as needed to level the
Remove the computer
wires that come from the computer
are properly connected to the
wires that come from the front handlebar
Check if the batteries are correctly
positioned and battery springs are
proper contact with batteries.
ies in the computer console
Change to new batteries.
Make sure that the wire
ulse sensor
ensure the pulse readout is more
precise, please always hold on to the
handlebar grip sensors with two hands
instead of just with one hand only when
you try to test your heart rate figures.
Gripping the hand pulse
Try to maintain moderate pressure
holding onto the hand
be loose on the
the bolts and tighten the loose
TROUBLE SHOOTING & MAINTENANCE
can be cleaned with a soft cloth and mild detergent. Do not use
wipe your perspiration off the
Be careful not get excessive moisture on the
might cause an electrical hazard or electronics to fail.
console, out of direct sunlight
nspect all assembly bolts and pedals on the machine for proper tightness
away from children
SOLUTION
rear stabilizer end cap on the r
as needed to level the recumbent
computer console and verify
wires that come from the computer
connected to the
wires that come from the front handlebar
batteries are correctly
positioned and battery springs are
with batteries.
computer console
Change to new batteries.
wire connection
ensors are secure.
ensure the pulse readout is more
precise, please always hold on to the
handlebar grip sensors with two hands
instead of just with one hand only when
you try to test your heart rate figures.
ulse sensors
moderate pressure
and pulse sensor
on the recumbent bike
the bolts and tighten the loose
can be cleaned with a soft cloth and mild detergent. Do not use
wipe your perspiration off the
Be careful not get excessive moisture on the
might cause an electrical hazard or electronics to fail.
console, out of direct sunlight
nspect all assembly bolts and pedals on the machine for proper tightness
away from children.
on the rear
recumbent
console and verify
wires that come from the computer
connected to the
wires that come from the front handlebar
batteries are correctly
positioned and battery springs are in
computer console may
Change to new batteries.
connections for
secure.
ensure the pulse readout is more
precise, please always hold on to the
handlebar grip sensors with two hands
instead of just with one hand only when
you try to test your heart rate figures.
s too tight.
moderate pressure while
ensors.
recumbent bike,
the bolts and tighten the loose
can be cleaned with a soft cloth and mild detergent. Do not use
Be careful not get excessive moisture on the
might cause an electrical hazard or electronics to fail.
console, out of direct sunlight
nspect all assembly bolts and pedals on the machine for proper tightness
.
may
too tight.
,
