EVSE 3704 Series User Manual And Installation Manual Download Page 11 | Manualshive

Page: 11 / 37

background image

3704-IG-001 Installation and User Manual

Page 5

3704-Mounting Poles Product Ordering Chart

If using a pole mounted configuration, select the appropriate Pole Kit based on EVSE type (single/dual) and mode of communication
(Zigbee/Serial) to the Payment/Gateway Module. Different poles are selected if a Payment Module/Gateway is on the same pole as
the EVSE, as noted below. EVSE, pole, Gateway/Payment modules are separate line items on the purchase order.

Single Pole Kits

ZigBee or On/Off
No (or Remote) Payment or Gateway

3841-300

Serial
No (or Remote) Payment or Gateway

3841-301

Serial or ZigBee
Compatible with Payment or Gateway
using Cellular Host Comm.

3841-302

Serial or ZigBee
Compatible with Payment or Gateway
using Ethernet Host Comm or Remote
Serial

3841-303

Dual Pole Kits

ZigBee or On/Off
No (or Remote) Payment or Gateway

3841-306

Serial
No (or Remote) Payment or Gateway

3841-307

Serial or ZigBee
Compatible with Payment or Gateway
using Cellular Host Comm.

3841-308

Serial or ZigBee
Compatible with Payment or Gateway
using Ethernet Host Comm or Remote
Serial

3841-309

«
...
9
10
11
12
13
...
»

Summary of Contents for 3704 Series






































Reviews:

No comments

Related manuals for 3704 Series

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 2

Brand: Cadillac Pages: 494

Brand: Cadillac Pages: 500

Brand: Cadillac Pages: 40

Brand: Cadillac Pages: 432

Brand: Cadillac Pages: 338

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 438

Brand: IBAIONDO Pages: 7

Document WorkCentre 450c

Brand: Xerox Pages: 2

Brand: Xerox Pages: 4

Brand: Harol Pages: 16

Ecoline UE-48Li80

Brand: UPOWER Pages: 6

Soft Luggage Pannier Racks

Brand: Honda Pages: 10

Brand: Paxton Automotive Pages: 85

Brand: Thule Pages: 8

AquaSensors AnalogPlus 1.0

Brand: Thermo Scientific Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands