EVOC EC7-1813CLD2NA SERIES User Manual Download Page 44

Page: 44 / 59

Chapter 3 BIOS Setup

EC71813CLD2NA SERIES

LVDS Color Depth

This option is used to select the color depth of LVDS.

Flat Panel Type

This option is used to select the resolution for Flat Panel.

UserDefine Panel Type

Configure the flat panel display type according to user definition.

PXE Boot

This option is used to select whether to enable LAN PXE boot function.

Onboard Audio Controller

Select whether to enable the audio card controller.

PCIPnP

BIOS SETUP UTILITY

Advanced PCI/PnP Settings

←→    Select Screen
↑↓    Select Item
+   Change Field
F1      General Help
F10    Save and Exit
ESC    Exit

WARNING: Setting wrong values in below sections may

cause system to malfunction.

IRQ3

[Available]

IRQ4

[Available]

IRQ5

[Available]

IRQ7

[Available]

IRQ9

[Available]

IRQ10

[Available]

IRQ11

[Available]

IRQ14

[Available]

IRQ15

[Available]

IRQ3 ~ 15

This option is used to specify whether the IRQ number is PNP mode or reserved

for ISA.

Summary of Contents for EC7-1813CLD2NA SERIES




























































Search results

Summary of Contents for EC7-1813CLD2NA SERIES

Reviews:

Related manuals for EC7-1813CLD2NA SERIES

Brands by name

Popular brands

EVOC EC7-1813CLD2NA SERIES, User Manual

Search results

Summary of Contents for EC7-1813CLD2NA SERIES

Reviews:

Related manuals for EC7-1813CLD2NA SERIES

Brands by name

Popular brands