EVOC EC7-1813CLD2NA SERIES User Manual Download Page 40 | Manualshive

Page: 40 / 59

background image

Chapter 3 BIOS Setup

EC71813CLD2NA SERIES

35

Ø

USB Configuration

BIOS SETUP UTILITY

USB Configuration

Enables USB host controllers.

←→    Select Screen
↑↓    Select Item
+   Change Field
F1      General Help
F10    Save and Exit
ESC    Exit

USB Devices Enabled:

1 Keyboard, 1 Drive

USB Function

[8 USB Ports]

USB 2.0 Controller

[Enabled]

Legacy USB Support

[Auto]

„

USB Mass Storage Device Configuration

V02.57 (c)Copyright 19852004, American Megatrends, Inc.

l

USB Function

This option sets the amount of USB controller; that is to confirm how many

USB controllers are supported. One controller usually supports two USB ports.

l

USB 2.0 Controller

This option is used to select whether to support USB 2.0 controller.

l

Legacy USB Support

This option is used to support legacy USB devices (such as keyboard, mouse

and storage devices, etc); when this option is set to Enabled, the USB device

could be used even if under OS that doesn’t support USB, such as DOS.

l

USB Mass Storage Device Configuration

This option is used to configure the USB mass storage device, including Reset

delay setting and enumeration type.

«
...
38
39
40
41
42
...
»

Summary of Contents for EC7-1813CLD2NA SERIES




























































Reviews:

No comments

Related manuals for EC7-1813CLD2NA SERIES

Brand: Atmel Pages: 22

Brand: Alcad Pages: 98

B360 GAMING PLUS

Brand: MSI Pages: 112

Brand: Supero Pages: 86

CYTVII-B-E-1M-SK

Brand: Cypress Pages: 19

Brand: Aaeon Pages: 65

Brand: Embest Pages: 91

TAS5508-5142K7EVM

Brand: Texas Instruments Pages: 20

Chipset TRF2436EVM

Brand: Texas Instruments Pages: 11

Spartan-7 SP701

Brand: Xilinx Pages: 4

Brand: Infineon Pages: 14

Brand: NXP Semiconductors Pages: 19

Brand: Ebyte Pages: 9

Brand: Texas Instruments Pages: 3

Brand: Infineon Pages: 30

Brand: Fujitsu Pages: 27

Brand: Fujitsu Pages: 34

Brand: Fujitsu Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands