EVOC EC7-1813CLD2NA SERIES User Manual Download Page 23

Page: 23 / 59

Chapter 2 Installation

EC71813CLD2NA SERIES

LAN Port and USB Port

The board provides two LAN ports and eight USB ports, among which one LAN port

and two USB ports share a set of socket (i.e. J3 and J4 include one LAN port and two

USB ports, respectively). In addition, the board also provides two 2x5 Pin USB

connectors, (J5 and J6), which can connect with four USB devices.

LAN Port

The board provides two 10/100/1000Mbps Ethernet connectors. ACTLED and LILED

are the LED indicators beside the Ethernet port, which respectively indicates the

activity status and the transmission status of LAN. Please refer to the status

description for each LED:

J3(LAN1)/J4(LAN2)

ACTLED

(Green)

LAN Activity

Status Indicator

LILED

(DualColor: O/G)

LAN Speed

Indicator

Green

1000Mbps

Blink

Data Transmitting

Orange

100Mbps

Off

No Data to Transmit

Off

10Mbps

USB Port

J3(USB1/USB2)
J4(USB3/USB4)

Pin

Signal Name

+5V

USB_Data

GND

Summary of Contents for EC7-1813CLD2NA SERIES




























































Search results

Summary of Contents for EC7-1813CLD2NA SERIES

Reviews:

Related manuals for EC7-1813CLD2NA SERIES

Brands by name

Popular brands

EVOC EC7-1813CLD2NA SERIES, User Manual

Search results

Summary of Contents for EC7-1813CLD2NA SERIES

Reviews:

Related manuals for EC7-1813CLD2NA SERIES

Brands by name

Popular brands