EVOC EC7-1813CLD2NA SERIES User Manual Download Page 35

Page: 35 / 59

Chapter 3 BIOS Setup

EC71813CLD2NA SERIES

Hyper Threading Technology

Control switch for the Intel Hyper Threading Technology function.

Intel(R) SpeedStep(tm) tech

Control switch for the Intel(R) SpeedStep(tm) tech function.

IDE Configuration

BIOS SETUP UTILITY

IDE Configuration

←→    Select Screen
↑↓    Select Item
+   Change Field
Tab    Select Field
F1      General Help
F10    Save and Exit
ESC    Exit

ATA/IDE Configuration

[Enhanced]

Configure SATA as

[IDE]

„

Primary IDE Master

:[Not Detected]

„

Primary IDE Slave

:[Not Detected]

„

Secondary IDE Master

:[Not Detected]

„

Secondary IDE Slave

:[Not Detected]

„

Third IDE Master

:[Not Detected]

„

Third IDE Slave

:[Not Detected]

ATA/IDE Configuration

This option is used to configure the operating mode for ATA; there are two

options: Enhanced and Compatible.

Configure SATA as

SATA controller type selection; there are two options for this item: IDE and

AHCI. Only when the ATA/IDE Configuration is under Enhanced mode, is

AHCI supported.

The AHCI function requires supports from hardware chip and OS.

Legacy IDE Channels

Summary of Contents for EC7-1813CLD2NA SERIES




























































Search results

Summary of Contents for EC7-1813CLD2NA SERIES

Reviews:

Related manuals for EC7-1813CLD2NA SERIES

Brands by name

Popular brands

EVOC EC7-1813CLD2NA SERIES, User Manual

Search results

Summary of Contents for EC7-1813CLD2NA SERIES

Reviews:

Related manuals for EC7-1813CLD2NA SERIES

Brands by name

Popular brands