EverFocus EMV1200 FHD User Manual Download Page 58

Page: 58 / 217

EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR

The following icons will be displayed at the bottom of the monitor to show the OBDII / CAN

bus status. To enable OBDII / CAN bus status, please consult EverFocus for more details

[email protected]

Turn Left

Turn Right

Reverse

Brake

Network

4G Network

WiFi

Network

GPS

No Signal of

Wireless

Network

Wireless

Network Off Low Beams High Beams

Tire No.

Tire Pressure Tire Temp.

Battery

Speed

RPM

To display the Tire Pressure icons, Please check (enable) the

OBDII

checkbox on the

Monitor

OSD

setting page (OSD Root Menu > System > Display > Monitor OSD). The status icons will

be automatically displayed in sequence every 5 seconds.

Summary of Contents for EMV1200 FHD


























































































































































































































Search results

Summary of Contents for EMV1200 FHD

Reviews:

Brands by name

Popular brands

EverFocus EMV1200 FHD, User Manual

Search results

Summary of Contents for EMV1200 FHD

Reviews:

Brands by name

Popular brands