EverFocus EMV1200 FHD User Manual Download Page 25

Page: 25 / 217

EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR

2.4

Vehicle Connection

The mobile DVR supports input power voltage between 9 VDC ~ 36 VDC. You can install the

mobile DVR in all kinds of vehicles support the above power voltage. The diagrams below are

examples to illustrate the connection inside car / truck with 12 VDC / 24 VDC.

* The following figures are using EMV1200 FHD for example; the differences between the two

models are the numbers of video input and audio input.

2.4.1

Connecting to a Truck with 24 VDC

Glove box (inside or underneath)

Driver’s seat (between the seat and the back panel) or underneath the Passenger

seat

9-12 CH

24V+ (Red)

IGN (Yellow)

EMV1200 FHD (Rear Panel)

GND (Black)

Vehicle Battery

24V

Power Harness Cable

Fuse (15A)

Lock

ACC

Powe

ACC

Note:

If the car is without an ignition key, please connect the IGN (yellow) wire directly or

via a switch to the vehicle battery.

Please note that since the power of mobile DVR is directly connected to the vehicle

battery, the mobile DVR will always draw power (2.5mA) from the vehicle battery.

Summary of Contents for EMV1200 FHD


























































































































































































































Search results

Summary of Contents for EMV1200 FHD

Reviews:

Brands by name

Popular brands

EverFocus EMV1200 FHD, User Manual

Search results

Summary of Contents for EMV1200 FHD

Reviews:

Brands by name

Popular brands