Evco EVJD900N2VW Applications Manual Download Page 19

Page: 19 / 74

EVCO S.p.A.

EV3 HRV & EVD HRV

| Application manual ver. 1.0a | Code 1443DHRVE104

page 19 of 74

On/stand-by:

ON if the controller is switched off (stand-by)

OFF if the controller is switched on

RUN (not available on EVD HRV):

always on

---

Days of the week (screen printed on the front of the EVJ LCD):

ON LED indicating the day of the week if the clock is enabled

The LED flashes indicating the day to be amended in the quick menu for

setting time bands

Not used

4.3

LED EVD HRV

The table below describes the 5 EVD HRV signalling LEDs along the side.

LED

Colour

Description

GREEN

Hardware LED

on if the device is powered up.

RUN

GREEN

RUN LED

ON if the controller is switched on

OFF if the controller is switched off (stand-by)

RED

Alarm LED

ON if an alarm is in progress

OFF if no alarm is in progress

AMBER

Intrabus LED

FLASHING if communication in progress

OFF if no communication in progress

RS-485

AMBER

Modbus LED

FLASHING if communication in progress

OFF if no communication in progress

Summary of Contents for EVJD900N2VW











































































Search results

Summary of Contents for EVJD900N2VW

Reviews:

Related manuals for EVJD900N2VW

Brands by name

Popular brands

Evco EVJD900N2VW, Applications Manual

Search results

Summary of Contents for EVJD900N2VW

Reviews:

Related manuals for EVJD900N2VW

Brands by name

Popular brands