'LDJQRVWLFV
#
DQG
#
)DXOW
#
)LQGLQJ
##
904
953#
9HFWRU
#
'ULYH
#0#
+$
7968;7
&KDSWHU
#9
'LDJQRVWLFV
#
DQG
#
)DXOW
#
)LQGLQJ
,1752'8&7,21
The 620 Vector Drive provides comprehensive diagnostic, alarm, and trip facilities. These facilities minimise the
possibility of damage to the drive, motor and associated components under unusual or fault conditions. The
diagnostics and alarm information, available at the MMI display, enable ready identification of conditions. In the
event that a fault is traced to the drive, the drive should be returned to the manufacturer - no corrective maintenance
should be attempted.
....DIAGNOSTICS [5 ] = 0
......TOTAL SPD.DMD. [6 ] = 0.00 %
h.....SPEED FB UNFIL [7 ] = 0.00 %
......SPEED FEEDBACK [11 ] = 0.00 %
......SPEED ERROR [8 ] = 0.00 %
......TORQUE DEMAND [9 ] = 0.00 %
......TORQUE FEEDBACK [10 ] = 0.00 %
......CURRENT FEEDBACK [78 ] = 0.00 %
f.....TERMINAL VOLTS [480] = 0 VOLTS
f.....DC LINK VOLTS [613] = 599 VOLTS
f.....TERM V INTEGRAL [623] = 100.00 %
......ACTUAL POS I LIM [13 ] = 11.96 %
......ACTUAL NEG I LIM [14 ] = -11.96 %
......INVERSE TIME O/P [15 ] = 11.96 %
......AT CURRENT LIMIT [16 ] = FALSE
......AT ZERO SPEED [17 ] = TRUE
......AT ZERO SETPOINT [18 ] = TRUE
......AT STANDSTILL [19 ] = TRUE
......STALL TRIP [20 ] = OK
......RAMPING [21 ] = FALSE
......DRIVE START [23 ] = FALSE
......DRIVE ENABLE [24 ] = FALSE
......OPERATING MODE [25 ] = STOPPED
......HEALTHY [27 ] = TRUE
......HEALTH OUTPUT [12 ] = TRUE
......READY [559] = FALSE
......RUN [28 ] = FALSE
f.....CO-PRO PRESENT [150] = TRUE
......ANIN 1 (C3) [29 ] = 0.000 VOLTS
......ANIN 3 (F2) [31 ] = 0.000 VOLTS
......ANIN 4 (F3) [32 ] = 0.000 VOLTS
......ANIN 5 (F4) [33 ] = 0.000 VOLTS
......ANOUT 1 (C5) [34 ] = 0.000 VOLTS
......ANOUT 2 (F5) [35 ] = 0.000 VOLTS
......COAST STOP [26 ] = TRUE
......PROGRAM STOP [22 ] = TRUE
......DIGIN B6 JOG [37 ] = FALSE
......DIGIN B7 START [36 ] = FALSE
......DIGIN B8 ENABLE [38 ] = TRUE
......DIGIN 1 (E2) [39 ] = TRUE
......DIGIN 2 (E3) [40 ] = FALSE
......DIGIN 3 (E4) [41 ] = FALSE
......DIGIN 4 (E5) [521] = FALSE
......DIGOUT 1 (E6) [42 ] = TRUE
......DIGOUT 2 (E7) [43 ] = TRUE
......DIGOUT 3 (E8) [44 ] = FALSE
......RAISE/LOWER O/P [45 ] = 0.00 %
......SPT SUM O/P 1 [46 ] = 0.00 %
......SPT SUM O/P 2 [385] = 0.00 %
......SPT SUM O/P 3 [386] = 0.00 %
......RAMP OUTPUT [47 ] = 0.00 %
......PRESET O/P [110] = 0.00 %
......SPEED SETPOINT [48 ] = 0.00 %
f.....SEQ RUN INPUT [49 ] = 0.00 %
f.....SEQ OUTPUT [50 ] = 0.00 %
......ENCODER [51 ] = 0 RPM
This manual was downloaded on www.sdsdrives.com
+44 (0)117 938 1800 - [email protected]