background image

SigNET 200/300 User Guide  

 14  

 

  ELAB 1543 

4.9.3 SMS Commands 

Once the SMS setup and configuration is complete, SMS features may be activated. Commands, depending 
on SMS configuration are sent using a code or caller ID. The type of code depends on the system SMS 
Authentication. An installation Engineer provides the appropriate setting and instructions for use. 
The table below provides all available SMS commands. Subsequent action and response are also provided. 
 
SMS Commands are sent as texts to the phone number of the SIM card on the controller. (Available with 
GSM modems only.) 
 
For commands using code, the format of the text is the code followed by either a space or a full stop.  Where 
**** is the code and “command” is the command: 

****.

command  or  **** command.  

For example, the command “HELP” is this text: 

**** HELP

 or ****

.HELP

 

 

Table 3 

COMMANDS (

**** = code

 

Using Code 

Using Caller ID 

Action 

Response 

**** HELP 
****.HELP 

HELP 

All available commands 
displayed  

All available commands 

**** FSET 
****.FSET 

FSET 

Fullset Alarm 

Time/date of system set. If 
applicable, responds with open 
zones/forceset zones 

**** USET 
****.USET 

USET 

Unset Alarm 

System Unset 

**** SSTA 
****.SSTA 

SSTA 

Status displayed 

Status of system and applicable 
areas 

**** LOG 
****.LOG 

 

Up to 10 recent events 
displayed 

Recent events 

**** ENG.ON 
****.ENG.ON 

ENG.ON 

Enable Engineer access 

Engineer status 

**** ENG.OFF 
****.ENG.OFF 

ENG.OFF 

Disable Engineer access 

Engineer status 

**** MANA.ON 
****.MANA.ON 

 

Enable Manufacturer access 

Manufacturer status 

**** MAN.OFF 
****.MAN.OFF 

 

Disable Manufacturer access 

Manufacturer status 

Summary of Contents for SigNET200 Series



















Reviews: