6
GB
7
GB
C
D
E
G
H
I
F
J
K
B
Q
O
N
M
L
P
A
R
A
Control and adjustment panel
B
Light (2 leds)
C
Air circulation hole + Active carbon filter
D
Sliding shelf
E
Closing clip
F
Storage shelf
G
Grid
H
Humidity cassette (1 temperature models)
I
Power lead
J
Base with front ventilation
K
Aeration filter access grille
L
4 adjustable levelling feet
M
Lower hinge (x2)
N
Specification label
O
Free air circulation hole
P
Door (fitted with handle and a double movement
lock)
Q
Upper hinge
R
Rear stop (5259S-V3, 5259V-V3)
The wine cabinet power lead has a plug to be plugged into a standard earthed socket to prevent
any risk of electric shock.
Have the mains socket inspected by a qualified electrician who will check that it is
correctly earthed and will carry out, if need be, work to bring your installation into line
with standards.
Contact your usual EuroCave dealer to change the power lead if it is damaged. It must be replaced
by a part which has an original manufacturer’s guarantee.
If you are moving to a foreign country, check whether or not the cabinet’s characteristics
correspond to the country (voltage, frequency).
Disposing of packaging
The packaging used by EuroCave is produced in
recyclable materials.
After unpacking your cabinet, take the packaging to
a refuse collection point. For the most part, it will be
recycled.
Recycling: a caring gesture
Electronic and electrical equipment has potentially harmful effects on
the environment and human health, owing to the presence of dangerous
substances.
Therefore, you must not trash electrical and electronic equipment with
non-sorted municipal waste.
When purchasing a new EuroCave product, you can entrust the recycling
of your old appliance to your EuroCave dealer.
Speak to your EuroCave dealer, he will advise you on the disposal and
collection arrangements set up within the EuroCave network.
In compliance with legislation on protecting and caring for the environment,
your wine cabinet does not contain C.F.C.s.
Energy-saving
Install your cabinet in a suitable location (see following page) and observe
the recommended temperature ranges.
•
Keep the door open only for very short periods.
•
Ensure that the door seal is intact and that it is not damaged. If it is,
contact your EuroCave dealer.
Disable unusable appliances by unplugging them and removing the power
lead.
For your personal sa
fety, the wine
cabinet
must be correctly ea
rthed.
Ensure that the
plug is correctly
earthed and that your
installation
is protected b
y a circuit brea
ker
(30 mA*).
*not applicable to
some countries.
2/ POWER SUPPLY
3/ PROTECTING THE ENVIRONMENT
AND SAVING ENERGY
4/ INSTALLING YOUR WINE CABINET
1/ DESCRIPTION OF YOUR WINE CABINET
Unpacking
•
Check, when your cabinet is delivered, that it does not have any external
faults (impact, warping…).
•
Open the door and check the integrity of the inside of your appliance
(walls, Main du Sommelier supports, hinges, bottle support…).
•
Remove the protective packing inside the humidor.
If there is a problem, contact your EuroCave dealer.
Installation
Transport your cabinet to the chosen location.
It must:
•
away from any heat source
•
be open on the outside to allow air to circulate (not a closed
cupboard...)
•
not be too damp (laundry room utility room, bathroom...),
•
have a stable, flat floor,
•
have a power supply (standard socket, 16 A, earthed with circuit
breaker, 30 mA* (*not applicable to some countries).
When moving the cabinet, do not tilt it mor
e than
45° and always on the lateral side, on the side of
the
flexible cord.
Precautions
•
Do not place your cabinet in an area likely to be flooded.
•
Do not position your cabinet near to a source of heat or expose it to the effects of direct sunlight.
•
Prevent water from splashing on the entire rear section of the appliance.
•
Position your appliance so that there is a minimum space of 5 – 10 cm between the wall and the rear wall of your cabinet.
•
If you are positioning your cabinet under a work surface, leave a minimum space of 5 cm all around the appliance including under the work surface. Allow
for a ventilation grill on the work surface (recommended).
•
Arrange the power lead so that it is accessible and does not come into contact with any component of the appliance.
