manualshive.com logo in svg

ete IR1759-MK5-AT3130-EDCont, Operation And Maintenance Manual

Share
Download
ete IR1759-MK5-AT3130-EDCont Operation And Maintenance Manual Download Page 11

        

IR1759-MK5-AT3130-EDCONT MINIRAY 

 

TE Connectivity - Aerospace, Defence & Marine

 /// Application Tooling 

Page 

11

 of 

36

 

 

 

3. Safety 

 

 

“READ THESE INSTRUCTIONS” 

WARNING:

 THIS PRODUCT IS A SOURCE OF VERY HIGH TEMPERATURE HEAT PRODUCED 

BY TUNGSTEN HALOGEN LAMP. AS WITH ANY ELECTRICAL EQUIPMENT, WHEN USING THIS 
HEATING TOOL, ALWAYS FOLLOW SAFETY PRECAUTIONS TO REDUCE THE RISK OF FIRE, 
ELECTRIC SHOCK OR PERSONAL INJURY. 

 

1.  Read and understand this instruction manual before using MINIRAY tool. 
2.  Do not expose heat tool to water and moisture including but not limited to rain and humid 

environments. Store indoors. Connect to grounded outlet only. Do not defeat this protection 
by using adapters or modifying the plug. 

3.  To extend the lamp life after using, run heat tool on cool for 1 to 2 minutes before turning-off. 

Never store product whilst hot. 

4.  Turn-off all controls before unplugging. 
5.  Unplug heat tool before performing any repair, servicing and when not in use. 
6.  Use heat tool on adequately rated circuits to avoid overheating of electrical system. 
7.  Do not use with damaged cored or plug. If equipment is not working as it should, has been 

dropped, damaged, left outdoors, or dropped into water, return it to a service centre. 

8.  Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around 

sharp edges or corners. Do not run equipment over cord. Keep cord away from heated 
surfaces. 

9.  Do not unplug by pulling on cord. To unplug grasp the plug, not the cord. 
10.  When an extension cord is used, it must be minimum 14-guage, 3-wire grounded cord rated 

for outdoor use. 

11.  Use heat gun in a well-ventilated area. Do not run when combustible materials, vapours or 

fumes are present. 

12.  Do not leave heat tool when plugged in. Do not leave heat tool in a running condition 

unattended. 

13.  Do not handle plug or heat tool with wet hands. 
14.  Do not touch the nozzle opening, shield, or attachments as high temperature and extreme 

heat are generated at those areas. Keep your hands and body out of the hot air stream. We 
recommend you wear safety glasses and protective gloves. 

15.  Do not use heat gun in presence of children. Do not allow to be used as a toy. Do not store 

within reach of children. Keep the heat tool in a safe, dry environment. 

16.  Do not heat chemicals that will ignite and /or release harmful vapours. 
17.  Use only as described in this manual. Use only manufacturer’s recommended attachments. 
18.  All service and/or repair work be performed by qualified personnel. 

 

 

 

 

3.1 Important Safety Instructions UL 499

 

Summary of Contents for IR1759-MK5-AT3130-EDCont





































Reviews:

No comments

Brands by name

Popular brands

Load more brands