background image

ETC Installation Guide

ColorSource PAR v1.7

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be
followed including the following:

READ AND FOLLOW ALL SAFETY
INSTRUCTIONS

Do not use outdoors.

Do not let power supply cords touch hot
surfaces.

Do not mount near gas or electric heaters.

Equipment should be mounted in
locations and at heights where it will not
readily be subjected to tampering by
unauthorized personnel.

The use of accessory
equipment not
recommended by the
manufacturer may cause
an unsafe condition.

Do not use this
equipment for other than
intended use.

SAVE THESE INSTRUCTIONS

The luminaire must be installed at

least 0.1 m (4.0 in) away from all

lighted objects.

Le luminaire doit être installé à au

moins 0,1 m (4,0 po) de tout objet

éclairé.

Do not mount the fixture on or

near a flammable surface.

Ne pas installer le projecteur sur ou à

côté d’une surface inflammable.

Risk of electric shock

Risque de décharge éléctrique

Do not stare at the operating light

source.

Ne pas regarder la source de lumière

lorsqu’elle fonctionne.

This product should not be

discarded as unsorted waste but

must be sent to separate collection

facilities for recovery and recycling.

Ce produit ne doit pas être jeté avec

les déchets ménagers mais doit être

déposé dans une collecte de déchets

électroniques ou dans un point de

collecte.

Protective earth (ground)

Protection Classe I Mise à la terre

ColorSource PAR

Page 3 of 12

ETC

Summary of Contents for ColorSource PAR













Reviews: