eta HACK 20 kW Service Manual Download | Manualshive

Page: 19 / 64

background image

Cleaning and maintenance

2500 h / annually

19

CAUTION!

Avoid operation with damaged seals

Never operate the boiler with damaged seals.
Otherwise, leak air is sucked in, disturbing the
combustion process and causing increased wear.



Always replace seals as soon as they are
damaged.

Close heat exchanger cover

Position the heat exchanger cover carefully.

Fig. 2-32: Heat exchanger cover

Turn both ball knobs through 180° to secure the heat
exchanger cover. Then tighten the two knurled nuts
evenly and cross-wise by turning them clockwise.

Fig. 2-33: Knurled nuts and ball knobs

Put the insulating cover back on.

Fig. 2-34: Insulating cover

«
...
17
18
19
20
21
...
»

Summary of Contents for HACK 20 kW

































































Reviews:

No comments

Related manuals for HACK 20 kW

Prestige Slol 250

Brand: TriangleTube Pages: 89

Naviels UKDAX-10EDT

Brand: DAXOM Pages: 47

Brand: Keston Pages: 8

Brand: Effecta Pages: 24

Brand: REMEHA Pages: 60

Brand: Vaillant Pages: 80

Brand: Squirrel Pages: 39

Brand: Flotec Pages: 12

Falcon 47-26701

Brand: Fer Pages: 44

AQUA HE 25 INOX ErP BE

Brand: Sime Pages: 100

Brand: Immergas Pages: 48

Brand: Rapido Pages: 36

Brand: Bryan Boilers Pages: 2

Brand: Bryan Boilers Pages: 2

Brand: Ideal Boilers Pages: 4

VITOCROSSAL 200

Brand: Viessmann Pages: 76

ISA 20 BITHERMAL

Brand: REXNOVA Pages: 36

CSI 123(T) Low Nox

Brand: Ravenheat Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands