background image

Warranty Registration Card must be filled out by the customer and mailed within thirty (30) days of installa-
tion in order to gain warranty coverage.

When receiving the PRESTIGE Solo unit, any claims for damage or shortage in shipment must be filed
immediately against the transportation company by the consignee.

Leave all documentation received with appliance with owner for future reference.

WARNING

* I N S

* I N S

T

T

A

A

L

L

L

L

A

A

T

T

I O N

I O N

A

A

N D M

N D M

A

A

I N

I N

T

T

E N

E N

A

A

N C E *

N C E *

M

M

A

A

N U

N U

A

A

L

L

NOTICE

2007-2 Manual Prestige Solo 60/175/250/399 - Revised 09/22/08 

If the information in this manual is not followed exactly, a fire or explosion may
result causing property damage, personal injury or death.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

- Do not try to light any appliance
- Do not touch any electrical switch; do not use any phone in your building.
- Immediately call your gas supplier from a neighbor’s phone. Follow the gas

supplier’s instructions.

- If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency or the
gas supplier.

prestige

Solo 60

Solo 175

Solo 250

Solo 399

Water Boiler

Series III

L

I

S T E

D

 

 

 

 

Summary of Contents for Prestige Slol 250


























































































Reviews: