eta HACK 20 kW Service Manual Download Page 35

Page: 35 / 64

Records

Cleaning (customer)

3.2

Cleaning (customer)

Cleaning is to be carried out once a year or after 2500 hours.

Comments:

Tasks

Notes

Empty the ash box

•

Remove excess ash from secondary combustion chamber

•

Empty the ash box

•

Check the seals

Check the pressure of the heating system

_________ bar

Check safety devices

•

Visual check of the safety valves

•

Visual check of the thermal relief valve

•

Check operational readiness of the safety devices in the fuel path

Chimney

•

Clean the flue tube

•

Flush the chimney's condensate drain

Clean combustion chamber

•

Clean inside of the secondary combustion chamber

•

Clean tilting grate

•

Clean secondary air openings

•

Clean the ignition tube

•

Check firebed button and firebed switch

•

Check refractory lining

Clean heat exchanger

•

Clean heat exchanger and downdraft channel

•

Clean lambda probe

•

Check heat exchanger tubes

•

Check heat exchanger cleaner

•

Check seal on heat exchanger cover

Clean flue gas recirculator (optional)

•

Clean flue gas recirculation piping

•

Inspecting seals on maintenance covers

performed on: _________________________

performed by: _________________________

Summary of Contents for HACK 20 kW

































































Search results

Summary of Contents for HACK 20 kW

Reviews:

Related manuals for HACK 20 kW

Brands by name

Popular brands

eta HACK 20 kW, Service Manual

Search results

Summary of Contents for HACK 20 kW

Reviews:

Related manuals for HACK 20 kW

Brands by name

Popular brands