background image

4    

 

Needed Tools and Parts Checklist 

Check off the items as you account for them and if you need to purchase an 
item add it to the shopping list side on the right 

Power Drill with 3/8, 1/4 and 5/16 inch bits

Crescent Wrench

Flat Head Screwdriver

Hacksaw/Sawzall

Phillips Head Screwdriver

Small Flathead Screwdriver

C-Ring Pliers

Tape Measure

Level

Wire Strippers

C-clamps

3/8”, 1/4”, 5/16” Drill Bits

Multi-meter (troubleshooting)

Digital  camera / cell phone camera (troubleshooting)

Shopping List 

Group Size 24 Deep Cycle Marine battery and battery terminal wire  
connectors (2 sets of connectors). 

Available at auto parts stores, battery stores, and some hardware stores. Max dimen-
sions 9H x 11.5Wx7D 
Different batteries have different lugs or spades, purchase connectors that crimp to 
wire for the battery you are buying. 

Positive post, bracket or door stop

.  

This would differ depending on your gate. It is an object for the gate to 
close against.  This is  recommended for a tight closed position.  

16 gauge, 2 conductor stranded direct burial low voltage wire  

Needed for wired accessories, the transformer to the control box, the solar panel to the control box. 

4 - 3/8” Carriage Bolts, Lock Washers and Nuts

 

This is for attaching your brackets to your post. If you have a block column purchase 3/8” anchors in-
stead. Purchase the bolts at the length needed to pass through your post. 

Water tight connectors / Wire strain reliefs  

When running wire into your control box, the holes the wires pass through should be secured to 
prevent water / elements of nature from entering. The number of strain reliefs would be  
determined by the number of wires entering the box. Box has 2) 1-1/4” and 4) 7/8” knockouts. 

4 - #10 Self-drilling Metal Screws 

Or other appropriate hardware. This is for attaching the control box to the post or fence. 

Outdoor Dome Plug Cover 

Or electrical box if you are using a transformer to charge the battery and the recep-
tacle is outdoors. Receptacles and transformers must always be kept dry. 

_____________________________________________________________ 

_____________________________________________________________ 

_____________________________________________________________ 

_____________________________________________________________ 

Summary of Contents for E-S Allegiant Series
















Reviews: