background image

12    

14. Set dip switches into the correct position for your gate opener:

DP 1 

ON: 

Auto-Close on (the gate will re-

close from the open position after a time 
set in the programming section) 

OFF: 

Auto-Close off 

DP 2 

ON: 

Dual gate opener  (2 motor s) 

OFF: 

Single gate opener  (1 motor ) 

DP 3 

ON: 

Gate lock terminals active 

OFF: 

Gate lock terminals inactive 

Power Connection 

15. Crimp the battery connectors (not included) to the battery wire. The only power connected to the Estate Swing E-S Allegiant control
board will be the battery* (not included). 

Important: 

Please respect polarity when attaching the battery terminals. Do not cross wires.

Connect the factory installed spade connectors to the control board as seen in diagram below.

*A Group Size 24 Deep Cycle Marine battery is required for this system. The battery size may be increased for power storage. 

Note:

Deep cycle marine batteries are available at auto part stores, home stores, and battery stores. 

If the battery sitting in the bottom of the

control box no longer leaves room for wires to be fed into the box, set the battery atop the battery lifts.

16. Connect the charging controls to the battery. See below for connection details

Transformer / Charge board: 

Transformer can be located up to 200 feet from the battery using 16 gauge 2 conductor wire. 
Connect positive and negative of transformer to positive and negative of solar terminals of charge board. 
Connect positive and negative of battery to positive and negative battery terminals of charge board. 
Respect polarity. Out terminals are not used. Charge board can be placed on top of battery. Transformer 
must be in an indoor location or under a plug cover. 

20 Watt or Higher / Charge board: 

Connect positive and negative of solar panel to positive and negative of solar terminals of charge board. 
Connect positive and negative of battery to positive and negative  battery terminals of charge board. 
Respect polarity. Out terminals are not used. Charge board can be placed on top of battery. 

5 and 10 Watt solar panel 

Connect the positive and negative of the solar panel 
directly to the battery respecting polarity.  

Solar panels can be placed up to 200 feet away using 16 gauge 2 conductor wire. 
Solar panels must be in full sun and directed south. 

20 Watt 

or 

Charge 

Board 

Control 

Board 

5 Watt 

10 Watt 

or 

Control 

Board 

Summary of Contents for E-S Allegiant Series
















Reviews: