Essilor AKR 550 Maintenance Manual Download Page 52

Page: 52 / 62

12-3 Removal of LCD ASSY, replacement of LCD relay board, LCD cover

unit and LCD unit

・

Removal of LCD ASSY

・

Disassembling procedure of LCD ASSY

From the condition

①

(Refer to 12-1)

1) Remove 1 connected earth harness and 2 harnesses.
2) Loosen the hexagon nut and then remove the LCD ASSY. (Condition

③

)

Note: Do not drop the resin washer, disc springs and metal washers in

the device when removing the LCD ASSY.

Condition

③

Harness

Hexagon nut

Metal washer

Resin washer

Disc spring
Place these 2
in the same
direction

Hexagon nut

＊

For assembling, follow the reverse procedures.

3) Unscrew 2 fixation screws (blue circle), and then remove the LCD tilt

top cover and the LCD bottom cover.

4) Unscrew 2 fixation screws (red circle), and then remove the LCD

bottom cover. (Condition

④

)

Earth harness

LCD ASSY

Summary of Contents for AKR 550































































Search results

Summary of Contents for AKR 550

Reviews:

Related manuals for AKR 550

Brands by name

Popular brands

Essilor AKR 550, Maintenance Manual

Search results

Summary of Contents for AKR 550

Reviews:

Related manuals for AKR 550

Brands by name

Popular brands