Essilor AKR 550 Maintenance Manual Download Page 54

Page: 54 / 62

12-4 Replacement of printer control board, thermal printer and

printer cover unit

・

Replacement of printer cover

・

Replacement of printer control board

・

Replacement of printer

＊

For assembling, follow the reverse procedures.

3) Unscrew 4 fixation screws, and

then remove the printer unit.

4) Unscrew 1 fixation screw, and then

replace the printer (main unit).

Thermal printer (main unit)

Condition

③

1) Remove the printer (platen unit)

after unscrewing 2 fixation screws.

2) Fix the removed platen unit on the

replaced printer cover unit.

1) Remove 1 connected harness, 1 connected earth

harness and 4 fixation screws (2 each for right and
left), and then remove the front panel ASSY

2) Remove 3 fixation screws and 1 connected harness,

and then replace the printer control board.

Front panel ASSY

Printer harness

Harness

Thermal printer (platen unit)

Earth harness

Printer control board

Summary of Contents for AKR 550































































Search results

Summary of Contents for AKR 550

Reviews:

Related manuals for AKR 550

Brands by name

Popular brands

Essilor AKR 550, Maintenance Manual

Search results

Summary of Contents for AKR 550

Reviews:

Related manuals for AKR 550

Brands by name

Popular brands