ERNITEC 1500M Installation And Setup Instructions Download Page 12

Page: 12 / 15

Iris

If the picture on the monitor is too dark or light, press:

Iris open

Iris close

Note: Available only if supported by the connected equipment.

Pan Camera

If the camera should be panned left or right, press:

1500M/1502M

1501M/1503M

1500M/1502M

1501M/1503M

Pan left

Pan right

JOYSTICK NOTE: When controlling a variable speed Pan/tilt, BDR-575 or ICU, pushing the
joystick towards its extremes will increase speed.

Tilt Camera

If the camera should be tilted up or down, press:

1500M/1502M

1501M/1503M

1500M/1502M

1501M/1503M

Tilt up

Tilt down

JOYSTICK NOTE: When controlling a variable speed Pan/tilt, BDR-575 or ICU, pushing the
joystick towards its extremes will increase speed.

Activating an AUX-relay

To activate AUX-relay 2, press:

AUX

Activate AUX 2 relay.

Note: If the Keyboard 1500 is set for

No Latch

operation the relay is

automatically de-activated when the AUX-key is released. If set for

Latch

operation the relay will remain activated when the key is released.

De-activating an AUX-relay

To de-activate AUX-relay 2, press:

AUX

De-activate AUX 2 relay.

Note: Used only if the Keyboard 1500 is set for

Latch

operation.

Installation and Setup instruction for Keyboard Series 1500

Page 12

Summary of Contents for 1500M
















Search results

Summary of Contents for 1500M

Reviews:

Related manuals for 1500M

Brands by name

Popular brands

ERNITEC 1500M, Installation And Setup Instructions

Search results

Summary of Contents for 1500M

Reviews:

Related manuals for 1500M

Brands by name

Popular brands