manualshive.com logo in svg

Epson Stylus COLOR 3000, Service Manual, Page: 81 / 180

Share
Download
Epson Stylus COLOR 3000 Service Manual Download Page 81

Disassembly and Assembly

Rev. A

3-12

3.2.7  PSB/PSE Board Assembly Removal

1.  Remove the upper housing. (See Section 3.2.1.)
2.  Remove the printer mechanism unit. (See Section 3.2.6.)
3.  Remove 7 screws (6 CBS screws , 3X8 and 1 CBP screw, 3X12) securing the upper shield plate to the

lower housing.

4.  Disconnect the power cable and connector cable for the main board assembly from the CN1 and CN2,

respectively.

5.  Remove 4 screws (CBS, 3X6) securing the PSB/PSE board assembly to the lower housing, then

remove the PSB/PSE board.

WARNING

After disconnecting the power cable from the AC socket, never disconnect the cable from
the CN1 for about 5 minutes, since the capacitor on the C172 PSB/PSE board is still
discharging electricity.

CBS Screws (3X6)

Upper Shield Plate

CBP Screw (3X12)

CN2

PSB/PSE Board Assembly

CN1

CBS Screws (3X6)

CBS Screws (3X6)

CBS Screw (3X6)

Figure 3-9. PSB/PSE Board Removal

Summary of Contents for Stylus COLOR 3000





















































































































































































Reviews:

No comments