manualshive.com logo in svg

Epson Stylus COLOR 3000, Service Manual, Page: 105 / 180

Share
Download
Epson Stylus COLOR 3000 Service Manual Download Page 105

Disassembly and Assembly

Rev. A

3-36

3.2.11.16  PF Roller Removal

1.  Remove the printer mechanism unit. (See Section 3.2.6.)
2.  Remove the paper eject frame unit. (See Section 3.2.11.6.)
3.  Remove the CR unit. (See Section 3.2.11.14.)
4.  Remove the base frame assembly. (See Section 3.2.11.15, Step 4 to 10.)
5.  Remove the roller contact spring in the left part of the PF roller.
6.  Remove the trigger lever from the PF roller.
7.  Turn the PF roller bushings at the right and left ends of the PF roller and release joints with right/left

frame assemblies and left main frame assembly.

8.  Remove 1 E-ring attached to the left end of the PF roller.
9.  Shift the PF roller left and release the joints for the PF roller gear (24) and ASF transmission ratchet.

Then remove the PF roller.

Do not touch the gears with your bare hands. Otherwise they will be damaged and lose
accuracy.

Trigger Lever

ASF Transmission Ratchet

Left Main Frame Assembly

Gear (56.4)

Roller Contact spring

Gear (24)

PF Roller Bushings

PF Roller Bushing

Trigger Transmission Lever

PF Roller

E-ring

Figure 3-34. PF Roller Removal

CAUTION

Summary of Contents for Stylus COLOR 3000





















































































































































































Reviews:

No comments