manualshive.com logo in svg

Epson Stylus COLOR 3000, Service Manual, Page: 73 / 180

Share
Download
Epson Stylus COLOR 3000 Service Manual Download Page 73

Disassembly and Assembly

Rev. A

3-4

3.2.1  Upper Housing Removal

1.  Remove the knob,

 tip of the PG adjust lever

, rear sheet guide, stacker and paper support.

2.  Using tweezers, release the hooks which fixes the tractor unit to the printer mechanism. Then remove

the tractor unit by lifting up the rear part of the tractor unit.

3.  Open the ink cartridge cover and release the hooks fixing the panel unit to the upper housing by

inserting the tweezers into the cutouts in the illustrated part of the panel unit. Then disconnect the
connector cable for the panel unit from the panel unit and remove the panel unit.

Tractor Unit

Hook in the Tractor Unit

Tweezers

Rear

Front

Figure 3-2. Tractor Unit Removal

Panel Unit

Upper Housing

Connector Cable for 

the Panel Unit

Tweezers

Ink Cartridge Cover

Figure 3-3. Panel Unit Removal

Summary of Contents for Stylus COLOR 3000





















































































































































































Reviews:

No comments