manualshive.com logo in svg

Epson Stylus COLOR 3000, Service Manual, Page: 42 / 180

Share
Download
Epson Stylus COLOR 3000 Service Manual Download Page 42

EPSON Stylus COLOR 3000

Rev. A

2-1

2.1 Overview

This chapter describes the operating principle of the printer mechanism and electrical circuit.

2.2  Printer Mechanism Operating Principle

2.2.1  Printer Mechanism

The printer mechanism of this printer is composed of the printhead unit, paper feeding mechanism, 

(

arriage) mechanism and the pump mechanism. The block chart for the printer mechanism is shown in

Figure 2-1. The printer mechanism has 3 motors: 

 motor, PF (Paper Feed) motor and pump motor.

Torque from the 

 motor moves the 

 in the column direction. PF motor sends torque to load, feed and

eject paper. The pump motor drives the pump mechanism. The release lever switches torque from the PF
motor side to the tractor side to feed continuous paper.

Release Lever

Disengage Mechanism

PF Motor

CR Motor

Color

Push Tractor Mechanism

Paper Feed Mechanism

ASF Mechanism

(For Cut sheet only.)

Pump Mechanism

CR Unit

Pump Motor

Black

Printhead Printhead

Figure 2-1. Printer Mechanism Block Diagram

Summary of Contents for Stylus COLOR 3000





















































































































































































Reviews:

No comments