manualshive.com logo in svg

Epson Stylus COLOR 3000, Service Manual, Page: 69 / 180

Share
Download
Epson Stylus COLOR 3000 Service Manual Download Page 69

Chapter 3

Disassembly and Assembly

 

3.1 Overview................................................................................................................3-1

 

3.1.1 Precautions for Disassembling the Printer.......................................................................... 3-1

 

3.1.2 Tools ........................................................................................................................................ 3-2

 

3.2 Disassembly and Assembly.................................................................................3-3

 

3.2.1 Upper Housing Removal........................................................................................................ 3-4

 

3.2.2 ROM Replacement.................................................................................................................. 3-6

 

3.2.3 CR PW (Paper Width) Sensor Board Assembly Removal................................................... 3-7

 

3.2.4 Printhead Removal ................................................................................................................. 3-8

 

3.2.5 HP Sensor Removal ............................................................................................................. 3-10

 

3.2.6 Printer Mechanism Removal ............................................................................................... 3-11

 

3.2.7 PSB/PSE Board Assembly Removal................................................................................... 3-12

 

3.2.8 C203 MAIN Board Assembly Removal................................................................................ 3-13

 

3.2.9 Main Waste Ink Drain Pad Removal.................................................................................... 3-15

 

3.2.10 PL (Paper Length) Sensor Removal ................................................................................. 3-16

 

3.2.11 Printer Mechanism Disassembly....................................................................................... 3-17

 

3.2.11.1 CR Motor Removal ................................................................................................ 3-17

 

3.2.11.2 Pump Motor Assembly Removal ........................................................................... 3-18

 

3.2.11.3 PF Motor Assembly Removal ................................................................................ 3-19

 

3.2.11.4 Front/Rear PE Sensor Removal ............................................................................ 3-20

 

3.2.11.5 Release Sensor Removal ...................................................................................... 3-21

 

3.2.11.6 Paper Eject Frame Unit Removal .......................................................................... 3-22

 

3.2.11.7 Pump Unit Removal............................................................................................... 3-23

 

3.2.11.8 Edge Guide Unit Removal ..................................................................................... 3-24

 

3.2.11.9 PQ (Paper Quantity) Sensor Board Assembly Removal ....................................... 3-26

 

3.2.11.10 ASF PW (Paper Width) Sensor Removal............................................................ 3-27

 

3.2.11.11 Ink Cartridge Holder Unit Removal ...................................................................... 3-28

 

3.2.11.12 Ink Sensor Assembly Removal............................................................................ 3-30

 

3.2.11.13 Ink Cartridge Sensor Assembly Removal............................................................ 3-30

 

3.2.11.14 CR Unit Removal ................................................................................................. 3-31

 

3.2.11.15 LD shaft Removal ................................................................................................ 3-33

 

3.2.11.16 PF Roller Removal............................................................................................... 3-36

 

3.2.11.17 Rear Paper Guide Removal ................................................................................ 3-37

 

3.2.11.18 Middle Frame Unit Removal ................................................................................ 3-38

Summary of Contents for Stylus COLOR 3000





















































































































































































Reviews:

No comments