manualshive.com logo in svg

Epson Stylus COLOR 3000, Service Manual, Page: 48 / 180

Share
Download
Epson Stylus COLOR 3000 Service Manual Download Page 48

EPSON Stylus COLOR 3000

Rev. A

2-7

2.2.4.2 Tractor Mechanism

Torque sent from the 

 motor to the 

 roller is transmitted to the tractor gear via disengage mechanism

operated with the release lever. When the release lever is set to the tractor side, the release sensor
detects the condition and torque transmission to the ASF mechanism is cut off as a result.

2.2.4.3  Manual Feed Mechanism

The printer loads cut sheet and roll paper in the rear paper slot. When the rear 

 sensor detects the

paper, the 

 unit leaves the ASF paper feed position. Therefore the paper is manually loaded even if

paper is set in ASF. This mode allows use of types of paper that differs from the one set in ASF.

Tractor Disengage Gear

Release Lever

Rear PE Sensor

PF Roller

PF Motor

PF Motor Pinion Gear

Tractor Gear

Figure 2-7. Tractor Mechanism

Summary of Contents for Stylus COLOR 3000





















































































































































































Reviews:

No comments