manualshive.com logo in svg

Epson Stylus COLOR 3000, Service Manual, Page: 102 / 180

Share
Download
Epson Stylus COLOR 3000 Service Manual Download Page 102

EPSON Stylus COLOR 3000

Rev. A

3-33

3.2.11.15  LD Shaft Removal

1.  Remove the printer mechanism unit. (See Section 3.2.6.)
2.  Remove the paper eject frame unit. (See Section 3.2.11.6.)
3.  Remove the CR unit. (See Section 3.2.11.14.)
4.  Remove 1 screw (CBP, 3x8) securing the 

ink supplying tube unit to the tube fixing holder

 on the printer

mechanism with the 

tube fixing holder

 (B). Then release the tubes from printer mechanism.

5.  Set the release lever to the tractor side and push the 

release transmission lever* 

inward. Then turn the

sub tractor release cam as shown in Figure 3-30 until it fits into the cutout on the left frame unit .Then
release the joint for the sub tractor cam and left frame unit.
* Release transmission lever: A black plastic lever located at the inner side of the left frame

6.  Pull out the tractor release shaft along with the tractor sub release cam.
7.  Remove 5 screws (CBS, 3X6) securing the base frame assembly to the printer mechanism unit. Then

remove the base frame assembly.

Tube Fixing Holder

Base Frame Unit

Tube Fixing Holder ;B

CBP Screw (3x8)

Figure 3-29. Ink Tube Unit Removal

Sub Tractor Release Cam

Tractor Release Shaft

Base Frame Unit

CBS Screw (3X6)

Middle Frame Unit

Right Main Frame

CBS Screws (3X6)

CBS Screws

 (3X6)

Left Frame Unit

Release Lever

Figure 3-30. Base Frame Assembly Removal

Summary of Contents for Stylus COLOR 3000





















































































































































































Reviews:

No comments