Epson LQ-300+II User Manual Download Page 29

Page: 29 / 162

Caution:

Never use the paper feed knob to adjust the tear-off position; this
may damage the printer or cause it to lose the tear-off position.

Note:

Your tear-off position setting remains in effect until you change it, even
if you turn off the printer.

1. Make sure the

Tear Off (Font)

lights are flashing (the paper

is at the current tear-off position). You may need to press the

Tear Off (Font)

button to advance the paper to the tear-off

position.

2. Open the paper guide cover.

3. Hold down the

Pause

button for about three seconds. The

Pause

light begins to flash and the printer enters the Micro

Adjust mode.

4. Press the

LF/FF

button to feed the paper backwards, or press

the

Load/Eject

button to feed the paper forwards, until the

paper perforation is aligned with the tear-off edge.

* tear-off edge

Summary of Contents for LQ-300+II



































































































































































Search results

Summary of Contents for LQ-300+II

Reviews:

Related manuals for LQ-300+II

Brands by name

Popular brands

Epson LQ-300+II, User Manual

Search results

Summary of Contents for LQ-300+II

Reviews:

Related manuals for LQ-300+II

Brands by name

Popular brands