Epson Equity III Product Support Bulletin Download Page 78

Page: 78 / 103

EPSON

EPSON AMERICA, INC.

SERVICE

RODUCT

UPPORT

ULLETIN

B NO.: S-0028A

DATE: 6/29/88

PAGE: 1 of 1

UBJECT: EPSON 3.5" 720KB FLOPPY DISK DRIVE COMPATIBILITY

The purpose of this bulletin is to provide information

regarding the compatibility

of the

Epson 3.5", 720KB

floppy disk drive (Product Code

A112A-AA)

with the Apex

and Equity series computers.

The 3.5" floppy disk drive must be used with MS-DOS 3.2

or higher.

Please refer to the following table for compatibility

information.

Apex

No special setup required

Equity

Not supported

Equity

Must include DRIVPARM =

/D:1

/F:2 in CONFIG.SYSI

Equity

III

Not supported*

Equity

I+

No special setup required

Equity

II+

No special setup required

Equity

III+

No special setup required

The Epson 3.5" floppy disk drive is not compatible with the

Equity

or the Equity

III.

* Manzana Microsystems Inc. offers a 3.5", 720KB floppy disk

drive which is compatible with the Equity

III

computer

when used with their 3FIVE device driver.

Refer to Product Support Bulletin # S-0027A for detailed

information on

using the DRIVPARM command to configure

Equity

systems for using the 3.5" floppy disk drive.

EPSON AMERICA SERVICE, 23610 TEL0 AVENUE, TORRANCE, CALIF. 90505

Summary of Contents for Equity III








































































































Search results

Summary of Contents for Equity III

Reviews:

Related manuals for Equity III

Brands by name

Popular brands

Epson Equity III, Product Support Bulletin

Search results

Summary of Contents for Equity III

Reviews:

Related manuals for Equity III

Brands by name

Popular brands