Epson Equity III Product Support Bulletin Download Page 95

Page: 95 / 103

E P S O N

EPSON AMERICA INC.

SERVICE DEPARTMENT

PRODUCT

SUPPORT

DATE:

4/3/87

NUMBER:

S-0008

SUBJECT:

EQUITY III+ CPU SPEED SELECTION ENHANCEMENT

ENHANCEMENT DESCRIPTION:

The Equity III+ computer has been enhanced to allow the

selection of CPU speeds while the computer is in operation.

In earlier units,

changing the CPU speed while the system was

in operation was not recommended because it could cause the

applications program to misexecute.

An information sheet describing the change is being included
with the new Equity III+ systems to inform the user to
disregard the warnings against changing the CPU speed during
operation as stated in the user documentation supplied with

the computer.

Equity III+ systems with the following serial numbers have
the enhanced capability.

From

024515

024799

026770

027100

027475

027574

027576

030100

030162

031815

The Equity III+ (10MHz) main board has been modified and the part
number has been changed as indicated below.

Old

New

(Y446800302)

(Y446800402)

Page 1 of 1

Summary of Contents for Equity III








































































































Search results

Summary of Contents for Equity III

Reviews:

Related manuals for Equity III

Brands by name

Popular brands

Epson Equity III, Product Support Bulletin

Search results

Summary of Contents for Equity III

Reviews:

Related manuals for Equity III

Brands by name

Popular brands