Epson Equity III Product Support Bulletin Download Page 90

Page: 90 / 103

E P S O N

EPSON AMERICA INC.

SERVICE DEPARTMENT

PRODUCT

SUPPORT

BULLETIN

DATE:

7/28/87

SUBJECT:

EQUITY III+ ROM BIOS NEW RELEASE

NUMBER:

S-0013A

The purpose

of this

bulletin is

to provide you with information

regarding the new Equity III+ ROM BIOS and how to obtain it.

The new ROM BIOS

was

released

primarily to

correct

a problem

encountered when

trying to use the Equity III+ as the file server

with the Dedicated version of

Novell

Netware

286 v2.0a. Equity

III+

systems

(below S/N 036981),

with the

earlier ROM BIOS

(Ver.

1.02),

failed to boot and displayed the following message:

ABEND INVALID OPCODE INTERRUPT
REBOOT TO RESTART

The new ROM BIOS upgrade

kit (P/N D27128B-150), which is user

installable, consists

of a

set of two 27128 ROMs (Ver. 1.50) and

installation instructions,

can be

ordered

from

Epson's Service

Department on an as needed basis.

DEALERS & AUTHORIZED SERVICE CENTERS:

All dealers

and ASC's

can order the upgrade free of charge on

an as-needed basis through the

Special

Order

Desk

using the

(800) number and dealer access code.

Indicate that this is part

of the Equity III+ ROM BIOS upgrade program

and the

ROMs will

be pre-shipped to the requested address.

Note:

Since this is a user installable upgrade there
dealer reimbursement program for this upgrade.

will be no

END-USERS:

End-users

should be

referred to Epson's Consumer Information

Department using our toll-free

number (800)

421-5426 to order

the ROM

BIOS upgrade.

They will

need to provide the Customer

Service Representative with their name, address

and the serial

number of the Equity III+.

Note:

The old ROMs must be returned to Epson America, Inc.

within 30 days or an invoice will be sent for the full list

price of the upgrade ROMs.

Page 1 of 1

Summary of Contents for Equity III








































































































Search results

Summary of Contents for Equity III

Reviews:

Related manuals for Equity III

Brands by name

Popular brands

Epson Equity III, Product Support Bulletin

Search results

Summary of Contents for Equity III

Reviews:

Related manuals for Equity III

Brands by name

Popular brands