Epson Equity III Product Support Bulletin Download Page 3

Page: 3 / 103

Product Support Bulletin

Subject: Change to Memory Expansion Board Recommendations for Equity

II+ and Equity Ill+

Date:

3/06/90

PSB No:

S-0113

Page:

1 of 1

Originator:

This bulletin provides information concerning expanded memory boards which

are recommended for use in the 12MHz models of the Equity II + and IlI+.

Please consider this information as an update to Product Support Bulletins
S-0042A and S-0051.

Due to the fact that the I/O bus speed of both the Equity II + and the Equity
Ill + is the same as the CPU speed selected, there are some problems in

compatibility with expanded memory boards when operating the systems at

12MHz.

Previously, Epson recommended the use of Micron Technology memory

expansion boards.

These boards have been removed from our recommended

product list due to the fact that Micron no longer produces ISA memory

boards.

One new addition to the recommended product list is the RAMpage 286 PIus
board from AST. This board was released in February 1990 and is compatible
with I/O bus speeds of 12MHz.

Summary of Contents for Equity III








































































































Search results

Summary of Contents for Equity III

Reviews:

Related manuals for Equity III

Brands by name

Popular brands

Epson Equity III, Product Support Bulletin

Search results

Summary of Contents for Equity III

Reviews:

Related manuals for Equity III

Brands by name

Popular brands