Epson Equity III Product Support Bulletin Download Page 36

Page: 36 / 103

NUMBER:

S-0061

PAGE:

9 of 13

Equity

III+ (10

MHz)

ROM

BIOS

Version: 1.50

Memory: 640KB Base, n o e x t e n d e d / e x p a n d e d

Clock Speeds: 6/8/10 MHz

Monitor: Color (CGA)

Video Adapter: Color (CGA)

DOS Version Tested: Epson MS-DOS 3.20

Mass Storage:

- 1.2MB FDD;

- 40MB HDD (Drive Type 17)

Hard Disk Controller: Epson WHDC

The Equity

III+ (10

MHz) is approved as a Novell file server,

with the following limitations:

The

III+ (10

MHz) will not function correctly at 10 MHz with

the Novell DCB, Orchid PC-NET and when Nestar and StarLan cards

are used together.

speeds.

They will function correctly at the slower

- The IBM CLUSTER card cannot be used in the

III+ (10

MHz).

NetWare Utilities

COMPSURF:

Passed

INSTALL:

Passed

Configurations tested with Advanced NetWare 86 2.0a

NETWARE DRIVER CONFIGURATIONS

STATUS

GENBIOS (86)/IBM

PC-NET:

Cold Boot:

Key Card (Critical!):

Printer:

86 Non-dedicated option:

SCSI

DIB Configuration:

IBM CLUSTER (86):

Passed

Failed

NetWare driver configuration for dial-in remote access:

NETWARE DRIVER CONFIGURATIONS

STATUS

GENBIOS (86)/IBM

PC-NET:

ASYNC:

Passed

Configurations tested with Advanced NetWare ND286 2.0a

NETWARE DRIVER

CONFIGURATIONS

STATUS

GENBIOS (ND286) :

SMC/PD Arcnet:

Passed

IBM

CLUSTER (ND286):

Failed

Comments: The

III+ (10

MHz) will not boot DOS with the

IBM

CLUSTER card installed.

Summary of Contents for Equity III








































































































Search results

Summary of Contents for Equity III

Reviews:

Related manuals for Equity III

Brands by name

Popular brands

Epson Equity III, Product Support Bulletin

Search results

Summary of Contents for Equity III

Reviews:

Related manuals for Equity III

Brands by name

Popular brands