Epson C82314* User Manual Download Page 3 | Manualshive

Page: 3 / 71

background image

FCC COMPLIANCE STATEMENT

FOR AMERICAN USERS

This equipment has bean tested and found to comply with the limits for

a Class A digital device. pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated

in

a commercial

environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not Installed and used in accordance with the
instruction manual, may cause harmful interference in which case the
user will be required to correct the interference at M

S

own expense.

This devise complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

FOR CANADIAN USERS

This digital apparatus does not exceed the Class A limits for radio noise

emissions from digital apparatus as set out in the radio interference
regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques

d&passant les limits applicables aux appareils numériques de Class A
prescrites dans le réglement sur le brouillage radioélectrique édicté par
le Ministére des Communications du Canada.

WARNING

The connection of a non-shielded equipment interface cable to this

equipment will invalldate the FCC Certification of this device and may
cause interference levels which exceed the limits established by the

FCC for this equipment. It is the responsibility of the user to obtain and
use a shielded equipment interface cable with this device. When this
equipment is attached to some printers, you should not leave cables
connected to the printer’s built-In connectors. See your printer’s user’s
manual for details.

Changes or modifications not expressly approved by Seiko Epson
Corporation, could void the user’s authority to operate the equipment.

«
1
2
3
4
5
...
»

Summary of Contents for C82314*








































































Reviews:

No comments

Related manuals for C82314*

Brand: Abocom Pages: 1

S5500-HI Switch Series

Brand: H3C Pages: 180

Brand: H3C Pages: 84

Brand: H3C Pages: 281

Brand: H3C Pages: 8

Brand: H3C Pages: 9

Brand: H3C Pages: 33

Brand: H3C Pages: 42

Brand: H3C Pages: 102

S12500CR Series

Brand: H3C Pages: 9

Brand: H3C Pages: 15

H3C S7500E Series

Brand: H3C Pages: 1565

Brand: H3C Pages: 4

Brand: ADTRAN Pages: 2

Brand: FOR-A Pages: 39

ER3-100 (5K02-55)

Brand: 8e6 Technologies Pages: 74

Brand: Abocom Pages: 1

DSL5068EN(1T1R)

Brand: Aztech Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands