Epson C82314* User Manual Download Page 7

Page: 7 / 71

GENERAL SPECIFICATIONS

Input Protocol:

IBM 3270 coax LU1 or LU3 protocol and Centronics
parallel protocol

Output Protocol:

Epson parallel, internal interface connection

Receive Data Rate:

Maximum burst: 2.3587 million bits/second

Data Buffering:

4K byte coax communication buffer

Language Support:

Standard IBM 3174 language sections (See

Appendix A, Command 8 for list of languages.)

Connectors:

Female BNC coax connector and mini-Centronics
parallel connector for alternate host (PC) sharing

Indicators:

One red LED
One green LED

Switches:

Two push buttons

Power Required:

+5V @ 240mA, supplied by the printer

LED SPECIFICATIONS

LED Indication

Green ON

Green OFF

Red ON

Red Blinks

Twice

Red Remains
on after turn on

status

The control unit (CU) is communicating with the interface card

(within past 30 seconds).

The CU is not communicating with the interface card.

The program attention (PA) manual option (see Appendix A,

command 35) is active and the printer received a request (from
the host software) for a PA button to be pressed by the user so
printing can continue.

The user pressed and released both buttons at the same time

(for less than 1 second) sending a cancel message to the host.

The interface encountered problems during its self test.

(The red LED goes off after a normal self test.)

Summary of Contents for C82314*








































































Search results

Summary of Contents for C82314*

Reviews:

Related manuals for C82314*

Brands by name

Popular brands

Epson C82314*, User Manual

Search results

Summary of Contents for C82314*

Reviews:

Related manuals for C82314*

Brands by name

Popular brands