Epson C82314* User Manual Download Page 15

Page: 15 / 71

PARALLEL INTERFACE SPECIFICATION

The C82314* coax interface provides a Centronics parallel data input port to allow

automatic sharing of the Epson printer between the 3270 host and an alternate

host. The parallel interface was designed to be compatible with popular printer

interfaces found on personal

computers. The following is a description of

the

parallel interface signals:

PARALLEL INTERFACE SPECIFICATIONS

Signal

Pin

Return

Pin

Signal

Parallel

Cable

Pin

Direction

Description

STROBE

Strobe pulse to
read data in. Pulse

width must be
more than .5 µsec.
at the interface

DATA1

These signals

DATA2

represent infor-

DATA3

mation in bits 1 to

5. 23

DATA4

8 of parallel data

DATA5

respectively. Each

DATA6

signal is HIGH

DATA7

when data is logical

DATA8

1 and LOW when it

is logical 0.

ACKNLG

OUT

A LOW pulse with a
minimum width of 4

µsec. A low indi-

cates that data has

been received and
that the printer is
ready to accept
more data.

Summary of Contents for C82314*








































































Search results

Summary of Contents for C82314*

Reviews:

Related manuals for C82314*

Brands by name

Popular brands

Epson C82314*, User Manual

Search results

Summary of Contents for C82314*

Reviews:

Related manuals for C82314*

Brands by name

Popular brands