Epson C82314* User Manual Download Page 38

Page: 38 / 71

COMMAND 34: INTERVENTION REQUIRED (IR) TIME OUT

Sets the time interval before an intervention required signal is sent to the host
after a printer error occurs.

VALUE DESCRIPTION

000

Never send an IR

001

255

Send IR after the VALUE times 5 seconds after printer error
occurs.

* 120

Default, send IR after ten minutes.

EXAMPLE: &%Z34,036

Sets IR time interval to 3 minutes

COMMAND 35: PROGRAM ATTENTION (PA) RESPONSE

The IBM host software can send a program attention (PA) request to the

printer, causing the printer to stop printing until a PA1 or PA2 response from

the printer is sent to the host software. The interface can be set to either
automatically return a PA1 response upon receiving a PA request or stop and
wait (with red LED on) until the operator presses one of the two push buttons

on the interface card.

VALUE DESCRIPTION

Printer stops and waits for operator to press a PA1 or PA2
push button before sending the PA response to the host.

Interface automatically responds with a PA1 if a PA request is
received from the host.

NOTE:

This can be used to enable an operator to install special forms,

colored paper, legal paper, etc. in the printer before the PA push
button is pressed.

EXAMPLE: &%,Z35,1

Printer automatically responds with a PA1 response.

A-14

Summary of Contents for C82314*








































































Search results

Summary of Contents for C82314*

Reviews:

Related manuals for C82314*

Brands by name

Popular brands

Epson C82314*, User Manual

Search results

Summary of Contents for C82314*

Reviews:

Related manuals for C82314*

Brands by name

Popular brands